It is the responsibility of the installation organization to have only technically qualified personnel performing the installation. Save the terminal s data and configuration. Equipment The following equipment comes with the clock system: Ordering Information No part of this document may be reproduced in any form or by any means without the express written consent of II Morrow Inc. Do not use or store the battery above the temperature of o F 70 o C. I typed everything in correctly…the new clock goes from cps1 to cps2…the current clock goes directly to cp31…when I hit the back button, it goes to password. Rotate the battery into position. Click the Advanced button to configure transmission delays if you experience problems communicating with the terminal.

Remove the old lead-acid battery by following steps 1 through 4 in the previous section, Testing the Lead-Acid Battery. In response to the prompt, type 0 and press Enter to exit supervisor mode and return to normal mode. TKC file to the host PC and look for any communication error messages. Manual Revisions Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. I set the 2 dip switches to match the old clock and hooked up the clock…I was able to set the time, but when I try to update the clock, I get an error, but it flashes on the screen so fast I cannot read it…help!!! Skip to main content. You can also use the SL utility to update the terminal s flash-eeprom. Here are some general guidelines to go by when setting up series modem clocks after a cold start.

For more information, see the documentation for the specific options. With your Tablet PC you will be. If so, obtain a detailed explanation of the problem.

Maintenance and Troubleshooting Guide Series 400 Terminal

Did you reverse post and post ti,ekeeper ADP provides this publication as is without warranty of any kind, either express. This premium will be added to the hammer price in your invoice.


Troubleshooting and Diagnostics Troubleshooting and Diagnostics The troubleshooting and diagnostics guide provides instructions to assist in tracking down the source of many basic controller installation problems. What are the current pay period dates, and what dates are these punches from? Browser access is also not forthcoming. Select the radio buttons for the primary and secondary serial ports for serial and modem communications.

PRM Press Enter and the file displays on the screen. Skip to main content. Refer to eBay Return policy for more details. Learn More – opens in a new window or tab International shipping and import charges paid to Seeries Bowes Inc. Example results of command See all makeanofferonit has no other items for sale. When you finish handling the assembly, replace it in the Series terminal, or place it on a grounded conductive surface.

Read more about the condition.

Prior to saving data, ensure that you installed the versions of SL To run the SL However, if you save just the terminal parameters, remember to reinitialize the terminal using your host application. Collect the punches or flush FIFO.

The size of a bus. A section specifically for customers is included on the things to do before calling Kronos Global Support and requesting a service call by a Customer Service Representative CSR.


You should rename the file so that the original file will not be modified. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. Alexander Weries 3 years ago Views: Locate the battery s red and black terminal tabs. Seller assumes all responsibility for this listing. RAM Size Lithium Battery Life days K 60 days K 30 days K 15 days When performing preventive maintenance on the Series terminal, you should determine the remaining life of the lithium battery.

Procedure 31 is for creating a base number that allows the terminal to distinguish seriez and guard badges from employee badges. To save the terminal parameters, complete the following steps: EXE to save and restore the Series terminal s data.


Use extreme caution when handling the battery to ensure that its cable leads do not come in contact with each other and that its terminal posts do not come in contact with metal. Interest will be charged to your account from the purchase date if the balance is not paid in full within 6 months.

The Terminal Parameters window appears: No part of More information. Enter the password and telephone number of the terminal you are restoring parameters to and press Enter. Can you tell me how to convert our 2c data to 3a? CFG file in the directory that you select. It reports the ports available and the baud rate on the Communications Resource Summary screen.

Changes that you make in virtual machines do not affect your physical computer. CopyrightStenograph, L.

Srries can record time and attendance data when an employee swipes a badge or enters a personal identification number PIN through the keypad.

Use the Terminal Service Utility to pull the parameters from the old clock. What did you try and what happened? Series Terminal Hardware Options various part numbers explains available Series terminal options in individual, stand-alone documents that contain product information as well as troubleshooting procedures and installation instructions.

The guide also includes a list and explanation of the procedures and steps that comprise these parameters, as well as configuration worksheets. User Manual March 31, v1. Timekeeper Terminal Quick Reference Card part number details operating mode functions, including how they appear on the Series terminal, and the appropriate responses to terminal prompts.

Also, verify the procedures you used to configure the terminal.